CBCT Reporting Level 1 — Online Course · self-paced · start today
New £195+VAT 7 hrs verifiable CPD Learn at your own pace
Start the course

Search 360 Visualise

↑ ↓ navigate ↵ open ESC close ⌘K shortcut
Get in touch
We'll get back to you within a few hours
Eighteeth OneFit sensor holder £70.83 + VAT

Eighteeth · Universal sensor holder

OneFit
sensor holder

Colour-coded rails and an aiming ring put your sensor in the right place for every view. Slide it together, take the image, then autoclave it and use it again.

OneFit kit · aiming ring, occlusal bracket and four sensor brackets

£70.83 + VAT  ·  £85.00 inc. VAT

Four brackets in the box, so it fits the NanoPix and VSensor sensors listed below.

Why dentists use it

Four colour-coded views

Match the colour. Aim at the ring.

Use it again

Autoclavable at 134 °C.

From Eighteeth  ·  Supplied and supported by 360 Visualise  ·  Call 01943 601222

Eighteeth OneFit universal sensor holder in its box
OneFit holder with a NanoPix sensor loaded in the intraoral bracket

How it works

Load. Match. Aim.

  • Load. Press the sensor into the intraoral bracket. It sits flat against the mounting surface.
  • Match. Slide the occlusal bracket into the rail of the colour you need. Thread the aiming ring onto the same colour.
  • Aim. Cover it with a disposable sleeve, place it in the mouth and line the X-ray tube up with the ring.
  • Clean. Take it apart, reprocess it and autoclave at 134 °C. It is ready for the next patient.
  • 4colour-coded views
  • 4sensor brackets
  • 134 °Cautoclavable
  • 19sensor models covered
  • 2 yearsexpected service life

One holder for each view

Pick the colour. Take the view.

Every bracket rail and every aiming ring slot has a colour. Match them and the geometry is set for you.

Red · Bitewing

The bitewing rail holds the sensor in the bitewing region.

Clean bitewings, the same set-up every time.

Blue · Anterior

The anterior rail holds the sensor for the front teeth.

Anterior periapicals without guesswork.

Yellow · Posterior

Right mandibular and left maxillary posterior teeth.

Two quadrants, one colour to remember.

Green · Posterior

Right maxillary and left mandibular posterior region.

The other two quadrants, covered.

Colour plus shape means a nurse can set it up and the dentist can trust it.

Start here

OneFit kit: £70.83 + VAT

Everything you need for all four views is in one box.

OneFit universal sensor holder

OneFit kit

£70.83 + VAT

£85.00 inc. VAT

  • 1 aiming ring
  • 1 occlusal bracket
  • 4 intraoral brackets: Clip 1, Clip 2, Clip 3 and Clip 4
  • Colour-coded for bitewing, anterior and posterior views
  • Autoclavable at 134 °C
Add OneFit to basket Book a demo Get a quote or call 01943 601222
Inside the OneFit box: aiming ring, occlusal bracket and four intraoral brackets

Buying an Eighteeth NanoPix sensor? Ask us about adding OneFit to your order.

Check before you buy

Which bracket fits your sensor?

The kit has four intraoral brackets, so one box covers the NanoPix and VSensor sensors below.

Clip 1
NanoPix Pro 1, NanoPix Pro 1.4, NanoPix-M Pro 1, NanoPix-M Pro 1.4, VSensor Pro 1, VSensor Pro 1.4, VSensor-M Pro 1, VSensor-M Pro 1.4
Clip 2
NanoPix Pro 2, NanoPix-M Pro 2, VSensor Pro 2, VSensor-M Pro 2, NanoPix 1.5, NanoPix-M 1.5
Clip 3
NanoPix 1, NanoPix-M 1, NanoPix-E 1.3
Clip 4
NanoPix 2, NanoPix-M 2

Not for Carestream RVG or Kodak sensors. They are too thick and too long for the OneFit brackets. For those, and for any other sensor, use DenBite, which fits any sensor. Not sure? Call 01943 601222 and we will tell you.

Between patients

Clean it. Sterilise it. Use it again.

OneFit is made to be reprocessed. Follow the manufacturer’s steps every time.

1. Cover it

Use a disposable hygiene sleeve over the sensor, the bracket and part of the occlusal bracket. Bin it after use.

2. Take it apart

Remove the small silicone sleeves from the intraoral bracket and reprocess the holder disassembled.

3. Clean it

Rinse off gross contamination with cold water below 40 °C. Use a washer-disinfector, or pre-clean with a soft brush.

4. Autoclave it

Pouch it and use a pre-vacuum steam cycle at 134 °C for 5 minutes, then dry for 20 minutes.

Check it each time. If you see cracks, discolouration or fracture, stop using it and call us.

Supplied and supported

A holder is only as good as the people behind it

360 Visualise supplies Eighteeth across the UK, alongside the NanoPix sensors the holder is made for. If you are not sure which bracket you need, or you want to add OneFit to a sensor order, you speak to a person who knows the product.

We also sell and support CBCT, intraoral scanners and X-ray systems. One supplier, one phone number.

Common questions

OneFit sensor holder questions answered

How much is OneFit?

£70.83 + VAT (£85.00 inc. VAT) from 360 Visualise.

What is in the box?

One aiming ring, one occlusal bracket and four intraoral brackets (Clip 1 to Clip 4). It covers bitewing, anterior and posterior views.

Which sensors does OneFit fit?

It fits the NanoPix and VSensor models listed in the compatibility table above. Each of the four brackets suits a different group of sensors. It does not fit Carestream RVG or Kodak sensors, which are too thick and too long. For those, or any sensor not listed, use DenBite, which fits any sensor.

How do I know which colour to use?

Red is bitewing. Blue is anterior. Yellow is right mandibular and left maxillary posterior. Green is right maxillary and left mandibular posterior. Match the colour on the bracket rail to the same colour on the aiming ring.

Can I autoclave it?

Yes. Reprocess it disassembled, with the small silicone sleeves removed. The manufacturer’s sterilisation cycle is 134 °C for 5 minutes, then dry for 20 minutes.

Do I still need a disposable sleeve?

Yes. Use a disposable hygiene sleeve over the sensor, the bracket and part of the occlusal bracket for every patient, and discard it after use.

How long does it last?

The manufacturer gives an expected service life of 2 years. Stop using it if you see cracks, bubbles, deformation or discolouration.

OneFit sensor holder. £70.83 + VAT.

Four colour-coded views. Four brackets in the box. Autoclave it and use it again.

Scroll to Top